Type: Driver
File Name:
File Size: 33.8 MB
66 (4.41)
Downloads: 44
Supported systems: Windows 10, Windows 8.1, Windows 8, Windows 7, Windows 2008, Windows Vista
Price: Free* (*Free Registration Required)

Download Now

One prime example is the challenging breast reconstruction ARTEC Scanner AT3E free tissue from the underbelly, called Deep Inferior Epigastric Perforator DIEP flap following a complete breast resection see figure 1 Figure 1: The right breast was completely resected and in a single-stage operation immediately reconstructed with DIEP- flap. A Preoperative scan, B 3 months after surgery, C and 2 weeks after contralateral breast symmetry correction and lipofilling of the DIEP-flap.

In Reconstructive Breast Surgery, there are several key steps in the intraoperative decisions about how to shape form, symmetry, and volume ARTEC Scanner AT3E the reconstructed breast compared to the opposite site. These decisions are made based mainly on the objective tape measurement, weighting or water- displacement measurement of specimens, and the subjective experience of the surgeon. The patient is viewed and measured in a lying and sitting posture, which allows a surgeon to envision a outcome based on gravity and skin laxity better. So far, there has been no research published about ARTEC Scanner AT3E use of 3-D imaging during surgery, as most 3-D Imaging devices are stationary or not mobile and thus impracticable of acquiring 3-D scans in an operation room 14, From the facts, we see a high potential of intraoperative 3-D Imaging assisting surgeons during Plastic and Reconstructive Surgery with objective parameters and a reliable decision making 2, Secondly, we aim to use those new mobile 3-D cameras to evaluate parts of the body which have been left out in recent years or have been hard to capture 3 such as the upper and lower extremity of patients.

Download ARTEC Digital Camera / Webcam / Camcorder drivers for Windows

These areas are for former 3-D systems, which could not cover degree angles and therefore would have to fill a room consisting of cameras, in several ways difficult to acquire: With the new hand-held scanners emerging sincethese obstacles were mastered step-by-step and current 3-D mobile systems can meet these requirements satisfactorily. Patients, Material and Methods ARTEC Scanner AT3E research team presents the use of different mobile scanning systems Sense, iSense, Artec Eva as a new mobile 3-D scanning method for plastic-surgical procedures. The Artec Eva is in addition powered by a battery pack.

ARTEC Scanner AT3E

So far, there has been no intraoperative 3D imaging system available to gather and visualize objective data such as form, volumes and symmetry to further ARTEC Scanner AT3E surgeons during procedures. Scans were directly processed during surgery and could be viewed and evaluated while the surgeons proceeded with their operation. We present several cases of intraoperative aesthetic breast shaping and breast reconstructions with implants and free tissue transfer, such as lipofilling and complete reconstructions with microsurgical free flaps. Avoid setting higher sensitivity values as the scan may result in duplicate images of the ARTEC Scanner AT3E surface.

It is recommended to perform scanning in a dark environment; close the curtains and turn off the lights.

ARTEC Drivers

Use a textured base like a piece of paper with drawings on it and, if necessary, slightly increase scanning sensitivity. In addition, reduce texture brightness or set it to zero when scanning. Artec Eva seems better suited to scan shining surfaces than Artec Spider. Scanning errors have been encountered while using Artec Spider in capturing teeth with a very whitish shining surface. Although the application of anti-glare spray results in a clear and highly accurate scan with Artec Spider, its use is not advisable on bones and teeth, since it may damage them and leave residues. Scanning of 3 shiny surfaces and thin edges are successfully improved by holding the scanner at a degree angle to the base with cameras directed to the bone, increasing the scanner sensitivity and reducing the ARTEC Scanner AT3E brightness to zero.

Artec AT3E Scanner Driver

Maintain the other scan options with their original setting values User Guide Artec Studio The geometry option alone will create a monochromatic model. Have the base removal option enabled in the scan options User ARTEC Scanner AT3E Artec Studio Base recognition will lead to the appearance of grey squares grid on the screen. The scanners can recognize the table surface and a piece of textured paper avoid simple texture as lines as a base, but will fail to recognize foam and a rotary table as a base no grey grid appear on screen but will instead recognize it as an object.


Base removal will automatically be performed when leaving the scan function. In preview mode, direct the scanner to the bone to identify ARTEC Scanner AT3E areas that may be difficult to scan to plan out how you can proceed with scanning. Always keep your eyes on the computer screen in order to see what the cameras are capturing and not what you see.


In the left menu, avoid using the autopilot option or the real-time fusion in the scan options. Manually perform the alignment and post processing of the captured scans. This allows for better user control in the creation of a 3D digital model of a ARTEC Scanner AT3E for research purposes. Artec AT3E Scanner Driver for Windows 9x/NT4. Read reviews (0)».

Operating system Windows NT / 9x; License: Freeware (free); Developer: Artec. Artec Ultima / USB Scanner Driver.

Artec Ultima / USB Scanner Driver for Windows 98/ME//XP 32bit. Artec Ultima USB Scanner Driver for Windows 98/ME//XP 32bit.

Related Posts